The tools and materials of the tangled ring are: red line, scissors, lighter. The specific steps are as follows: 1, first, fold the prepared red rope to make the folding end round. 2, put the red line on the ring that needs to be tied to the red line, and hold the round and ring with your fingers. 3, hold one end of the red line with another hand and start entangled. Pay attention to tightly. 4, after tie the red line, put the red line on the hand and pass through the circle on the left side of the starting point. 5, then hold the other end of the red line with your hand and tighten the circle on the ring. 6, cut off the excess red line with scissors. Pay attention to about 2 mm when cutting. 7, cut off the excess red line and burn the excess line with a lighter. 8. After the steps are done, the ring is entangled successfully.
Prepare materials: red rope, ring, lighter. 1, then take out the red rope, and then pinch the red rope into a circle, as shown in the figure. 2. Put the circle at the opening of the ring, as shown in the figure. 3, press the circle with your thumb, grab the other end of the red rope with the other hand, as shown in the figure. 4, wrap the red rope on the ring, as shown in the figure. 5, after wound, pass the line head through the circle, as shown in the figure. 6, grab the other end of the red rope to tighten the circle, as shown in the figure. 7, cut off the excess line head, pay attention to leaving 1 ~ cm head head on both sides. 8. Burn the head head with a lighter. 9, complete.
The tool materials that need to be prepared with a red line entangled ring are: red line, scissors, lighters. The specific method steps are as follows: 1, first fold the prepared red rope, so that the folding end shows a circle. 2. Place the red line at the ring that needs to be tied to the red rope, and pinch the folded circle and ring with your fingers. 3, pull one end of the red line with the other hand to start entangled, pay attention to the tightness. 4. After tie the red line, pass the red rope in your hand through the circle that you just left. 5, then pull the other end of the red line with your hand to tighten the circle on the ring. 6. Cut off the excess red thread with scissors. Pay attention to cutting about two millimeters when cutting. 7. After cutting the excess red line, burn the excess line head with a lighter. 8, after some operation, this ring is wrapped with a red rope.
n00:00 / 01: 1970% shortcut keys to describe space: Play / suspend ESC: Exit full screen ↑: increase volume 10% ↓: decreases by 10% → 5 seconds of fast advances ←: single fast retreat 5 seconds Press held up hold Here you can drag no longer appear in the player settings to reopen the small window shortcut key description
The tools and materials of the tangled ring are: red line, scissors, lighter.
The specific steps are as follows:
1, first, fold the prepared red rope to make the folding end round.
2, put the red line on the ring that needs to be tied to the red line, and hold the round and ring with your fingers.
3, hold one end of the red line with another hand and start entangled. Pay attention to tightly.
4, after tie the red line, put the red line on the hand and pass through the circle on the left side of the starting point.
5, then hold the other end of the red line with your hand and tighten the circle on the ring.
6, cut off the excess red line with scissors. Pay attention to about 2 mm when cutting.
7, cut off the excess red line and burn the excess line with a lighter.
8. After the steps are done, the ring is entangled successfully.
Prepare materials: red rope, ring, lighter.
1, then take out the red rope, and then pinch the red rope into a circle, as shown in the figure.
2. Put the circle at the opening of the ring, as shown in the figure.
3, press the circle with your thumb, grab the other end of the red rope with the other hand, as shown in the figure.
4, wrap the red rope on the ring, as shown in the figure.
5, after wound, pass the line head through the circle, as shown in the figure.
6, grab the other end of the red rope to tighten the circle, as shown in the figure.
7, cut off the excess line head, pay attention to leaving 1 ~ cm head head on both sides.
8. Burn the head head with a lighter.
9, complete.
The tool materials that need to be prepared with a red line entangled ring are: red line, scissors, lighters.
The specific method steps are as follows:
1, first fold the prepared red rope, so that the folding end shows a circle.
2. Place the red line at the ring that needs to be tied to the red rope, and pinch the folded circle and ring with your fingers.
3, pull one end of the red line with the other hand to start entangled, pay attention to the tightness.
4. After tie the red line, pass the red rope in your hand through the circle that you just left.
5, then pull the other end of the red line with your hand to tighten the circle on the ring.
6. Cut off the excess red thread with scissors. Pay attention to cutting about two millimeters when cutting.
7. After cutting the excess red line, burn the excess line head with a lighter.
8, after some operation, this ring is wrapped with a red rope.
n00:00 / 01: 1970% shortcut keys to describe space: Play / suspend ESC: Exit full screen ↑: increase volume 10% ↓: decreases by 10% → 5 seconds of fast advances ←: single fast retreat 5 seconds Press held up hold Here you can drag no longer appear in the player settings to reopen the small window shortcut key description